INSPECTION CHART FOR DIAGNOSTIC TROUBLE CODE

DTC No.	Fault description
B1111	Battery voltage too high
B1112	Battery voltage too low
B1346	Driver airbag (DAB), Resistance too high
B1347	Driver airbag (DAB), Resistance too low
B1348	Driver airbag (DAB), Short to GND
B1349	Driver airbag (DAB), Short to Battery
B1352	Passenger airbag (PAB), Resistance too high
B1353	Passenger airbag (PAB), Resistance too low
B1354	Passenger airbag (PAB), Short to GND
B1355	Passenger airbag (PAB), Short to Battery
B1361	Driver seat belt pretensioner (DBPT), Resistance too high
B1362	Driver seat belt pretensioner (DBPT), Resistance too low
B1363	Driver seat belt pretensioner (DBPT), Short to GND
B1364	Driver seat belt pretensioner (DBPT), Short Battery
B1367	Passenger seat belt prestensioner (PBPT), Resistance too high
B1368	Passenger seat belt prestensioner (PBPT), Resistance too low
B1369	Passenger seat belt prestensioner (PBPT), Short to GND
B1370	Passenger seat belt prestensioner (PBPT), Short to Battery
B1378	Driver side airbag (DSAB), Resistance too High
B1379	Driver side airbag (DSAB), Resistance t0o Low
B1380	Driver side airbag (DSAB), Short to GND
B1381	Driver side airbag (DSAB), Short to Battery
B1382	Passenger side airbag (PSAB), Resistance too high
B1383	Passenger side airbag (PSAB), Resistance too low
B1384	Passenger side airbag (PSAB), Short to GND
B1385	Passenger side airbag (PSAB), Short to Battery
B1400	Satellite left side sensor defect
B1401	Satellite sensor left side short to GND
B1402	Satellite sensor left side open/short to battery
B1403	Satellite right side sensor defect
B1404	Satellire sensor right side short to GND
B1405	Satellire sensor right side open/short to battery
B1409	Satellite left side sensor communication error
B1410	Satellite right side sensor communication error
B1511	Driver seat belt buckle switch open/short to battery
B1512	Driver seat belt buckle switch short to GND
B1513	Passenger seat belt buckle switch open/short to battery
B1514	Passenger seat belt buckle switch short to GND
B1620	Airbag unit internal failure
B1650	SRSCM crash recorded
B1655	Side airbag crash recorded
B1657	Crash recorded-Belt pretensioner only
B1661	ECU mismatching
B2500	Warning lamp failure

• The DAB is located in the steering wheel. • The PAB is located in the crash pad. • The DSAB is located in the left side of driver's seat. • The PSAB is located in the right side of passenger's seat.

DTC

B1111 B1112

Battery voltage too high (Vbaft ≥ 19.2V) Battery voltage too low (Vbaft ≤ 7.2V)

1.

Preparation (1) Disconnect the negative (-) terminal cable from the battery, and wait at least 30 seconds. (2) Remove the DAB module. (3) Disconnect the connectors of the PAB, left and right side airbags, belt pretensioners and satellite sensors. (4) Disconnect the SRSCM connector. Place the DAB with the front surface facing upward.

2.	Check source voltage. (1) Connect the negative (-) terminal cable to the battery. (2) Turn the ignition switch ON.

1.	Does the SRS warning light turn off ? [PREPARATION] (1) Turn the ignition switch to LOCK. (2) Connect the DAB module. (3) Connect the PAB connector, left and right side airbag, belt pretensioner and satellite connectors. (4) Connect the SRSCM connector. (5) Turn the ignition switch ON.

DTC	B1348	DAB short to ground
	B1354	PAB short to ground
	B1363	DBPT short to ground
	B1369	PBPT short to ground
	B1380	DSAB short to ground
	B1384	PASB short to ground
	B1401	Satellite sensor left side short to ground
	B1404	Satellite sensor right side short to ground

DTC Detecting Condition	Trouble Area
• Short circuit in squib wire harness (to ground) • Squib malfunction • Clock spring malfunction • SRSCM malfunction	• DAB squib • PAB squib • DSAB squib • PSAB squib • BPT squib • Satellite sensor • Clock spring • SRSCM • Wire harness

1.

Preparation (1) Disconnect negative (-) terminal cable from the battery, and wait at least 30 seconds. (2) Remove the DAB module. (3) Disconnect the connectors of the PAB, left and right side airbag, space belt pretensioner and satellite sensor. (4) Disconnect the connector of the SRSCM. Place the DAB with the front surface facing upward.

2.	Check DAB squib circuit. [CHECK] For the connector (on the clock spring side) between clock spring and DAB, measure the resistance between DAB high and body ground. Resistance : ∞

3.	Check the PAB squib circuit. [CHECK] For the connector (on the SRSCM side) between SRSCM and PAB, measure the resistance between PAB high and body ground. Resistance : ∞

4.	Check PSAB and DSAB squib circuits. [CHECK] For the connector (on the SRSCM side) between SRSCM and the SABs, measure the resistance between the SABs high and body ground. Resistance : ∞

5.	Check the BPTs squib circuit. [CHECK] For the connector (on the SRSCM side) between the SRSCM and BPT, measure the resistance between the BPTs high and body ground. Resistance : ∞

6.	Check the Satellite sensor circuit. [CHECK] For the connector (on the SRSCM side) between the SRSCM and the Satellite sensor, measure the resistance between the Satellite high and body ground. Resistance : ∞

7.

Check the SRSCM. [PREPARATION] A. Connect the connector to SRSCM. B. Using a service wire, connect the DAB high and DAB low on the clock spring side of connector. C. Using a service wire, connect the PAB high and low on SRSCM side of connector. D. Connect the SABs and BPT using the same method. E. Connect the negative (-) terminal cable to battery, and wait it least 30 seconds. [CHECK] A. Turn ignition switch to ON, and wait for at least 30 seconds. B. Clear any codes stored in the memory with the Hi-Scan Pro. C. Turn the ignition switch to LOCK, and wait for 30 seconds. D. Turn the ignition switch to ON, and wait for 30 seconds. E. Using the Hi-Sacn Pro, check for DTCs. There is no DTC. [HINT] Codes other than these may be output at this time, but they are not relevant to this check.

8.

Check the DAB squib. [PREPARATION] A. Turn the ignition switch to LOCK. B. Disconnect the negative (-) terminal cable from the battery, and wait for 30 seconds. C. Connect the DAB connector. D. Connect the negative (-) terminal cable to the battery, and wait for 30 seconds. [CHECK] A. Turn the ignition switch to ON, and wait for at least 30 seconds. B. Clear the malfunction code stored in the memory of the Hi-Scan Pro. C. Turn the ignition switch to LOCK, and wait for 30 seconds. D. Turn the ignition switch to ON, and wait for 30 seconds. E. Using the Hi-Scan Pro, check for DTCs. There is no DTC. [HINT] Codes other than these may be output at this time, but they are not relevant to this procedure.

9.

Check the PAB squib. [PREPARATION] A. Turn the ignition switch to LOCK. B. Disconnect the negative (-) terminal cable from the battery, and wait for 30 seconds. C. Connect the PAB connector. D. Connect the negative (-) terminal cable from the battery, and wait for 30 seconds. [CHECK] A. Turn the ignition switch to ON, and wait for at least 30 seconds. B. Clear the malfunction code stored in the memory with the Hi-Scan Pro. C. Turn the ignition switch to LOCK, and wait for 30 seconds. D. Turn the ignition switch to ON, and wait for 30 seconds. E. Using the Hi-Sacn Pro, check for DTCs. There is no DTC. [HINT] Codes other than these may be output at this time, but they are not relevant to this procedure.

10.

Check the SABs squib. [PREPARATION] A. Turn the ignition switch to LOCK. B. Disconnect the negative (-) terminal cable from the battery, and wait for 30 seconds. C. Connect the SAB connector. D. Connect the negative (-) terminal cable from the battery, and wait for 30 seconds. [CHECK] A. Turn the ignition switch to ON, and wait for at least 30 seconds. B. Clear the malfunction code stored in the memory with the Hi-Scan Pro. C. Turn the ignition switch to LOCK, and wait for 30 seconds. D. Turn the ignition switch ON, and wait for 30 seconds. E. Using the Hi-Sacn Pro, check for DTCs. There is no DTC. [HINT] Codes other than these ones may be output at this time, but they are not relevant to this checking procedure. Check the DSAB using the same procedure.

11.

Check BPT squib. [PREPARATION] A. Turn the ignition swich to LOCK. B. Disconnect the negative (-) terminal cable from the battery, and wait for 30 seconds. C. Connect the BPTs connector. D. Connect the negative (-) terminal cable from the battery, and wait for 30 seconds. [CHECK] A. Turn the ignition switch to ON, and wait for 30 seconds. B. Clear the malfunction code stored in the memory with the Hi-Scan Pro. C. Turn the ignition switch to LOCK, and wait for 30 seconds. D. Turn the ignition switch to ON, and wait for 30 seconds. E. Using the Hi-Scan Pro, check for DTCs. There is no DTC. [HINT] Codes other than these may be output at this time, but they are not relevant to this procedure.

12.

Check the Satellite sensors. [PREPARATION] A. Turn ignition switch to LOCK. B. Disconnect negative (-) terminal cable from the battery, and wait at least 30 seconds. C. Connect the Satellite sensor connector. D. Connect the negative (-) terminal cable from the battery, and wait at least 30 seconds. [CHECK] A. Turn the ignition switch to ON, and wait at least 30 seconds. B. Clear the malfunction code stored in memory with the Hi-Scan Pro. C. Turn the ignition switch to LOCK, and wait at least 30 seconds. D. Turn the ignition switch to ON, and wait at least 30 seconds. E. Using the Hi-Scan Pro, check for DTCs. There is no DTC. [HINT] Codes other than these may be output at this time, but they are not relevant to this procedure.

13.	Check clock spring circuit. [PREPARAION] Disconnect connector between SRSCM and clock spring. [CHECK] Measure resistance between the DAB high on the clock spring side of connector between clock spring and DAB and body ground. Resistance : ∞

DTC	B1349	DAB short to battery
	B1355	PAB short to battery
	B1364	DBPT short to battery
	B1370	PBPT short to battery
	B1381	DSAB short to battery
	B1385	PSAB short to battery
	B1402	Satellite left side short to battery
	B1405	Satellite right side short to battery

DTC Detecting Condition	Trouble Area
• Short circuit in squib wire harness (to B+) • Squib malfunction • Clock spring cable malfunction • SRSCM malfunction	• DAB squib • PAB squib • DSAB or PSAB squib • BPT squib • Satellite sensor • Wire harness

1.

Preparation (1) Disconnect negative (-) terminal cable from the battery, and wait at least 30 seconds. (2) Remove the DAB module. (3) Disconnect the connectors of the PAB, left and right side airbag,belt pretensioner and satellite sensor. (4) Disconnect the connector of the SRSCM. Place the DAB with the front surface facing upward.

2.	Check the DAB squib circuit. [CHECK] For the connector (on the clock spring side) between the clock spring and DAB, measure the voltage between the DAB high and body ground. Voltage : 0 V

3.	Check the PAB squib circuit. [CHECK] For the connector (on the SRSCM side) between the SRSCM and PAB, measure the voltage between the PAB high and body ground. Voltage : 0 V

4.	Check the SAB squib circuit. [CHECK] For the connector (on the SRSCM side) between the SRSCM and SAB, measure the voltage between the SAB high and body ground. Voltage : 0 V

5.	Check the BPTs squib circuits. [CHECK] For the connector between SRSCM and the BPTs, measure the voltage between the BPTs high and body ground. Voltage : 0 V

6.	Check the Satellite sensor circuit. [CHECK] For the connector between the SRSCM and the Satellite sensor, measure the voltage between the Satellite sensor high and body ground. Voltage : 0 V

7.

Check the SRSCM. [PREPARATION] A. Connect the connector to the SRSCM. B. Using a service wire, connect the DAB high and low on the clock spring side of connector between the clock spring and the DAB. C. Using a service wire, connect the PAB high and low on the SRSCM side of the connector between the SRSCM and the PAB. D. Using a service wire, connect the SAB high and low on the SRSCM side connector between the SRSCM and the SAB. E. Using a service wire, connect the BPT high and low on the SRSCM side connector between the SRSCM and the BPT. F. Using a service wire, connect the satellite high and low on the SRSCM side connector between the SRSCM and the satellite sensor. G. Connect negative (-) terminal cable to battery, and wait at least 30 seconds. [CHECK] A. Turn the ignition switch to ON, and wait at least 30 seconds. B. Clear the malfunction code stored in memory with the Hi-Scan Pro. C. Turn the ignition switch to LOCK, and wait at least 30 seconds. D. Turn the ignition switch to ON, and wait at least 30 seconds. E. Using the Hi-Scan Pro, check for DTCs. There is no DTC. [HINT] Codes other than these may be output at this time, but they are not relevant to this check.

8.

Check the DAB squib. [PREPARATION] A. Turn the ignition switch to LOCK. B. Disconnect the negative (-) terminal cable from the battery, and wait for 30 seconds. C. Connect the DAB connector. D. Connect the negative (-) terminal cable to the battery, and wait for 30 seconds. [CHECK] A. Turn the ignition switch ON, and wait for at least 30 seconds. B. Clear the malfunction code stored in the memory of the Hi-Scan Pro. C. Turn the ignition switch to LOCK, and wait for 30 seconds. D. Turn the ignition switch to ON, and wait for 30 seconds. E. Using the Hi-Scan Pro, check for DTCs. There is no DTC. [HINT] Codes other than these may be output at this time, but they are not relevant to this procedure.

9.

Check the PAB squib. [PREPARATION] A. Turn the ignition switch to LOCK. B. Disconnect the negative (-) terminal cable from the battery, and wait for 30 seconds. C. Connect the PAB connector. D. Connect the negative (-) terminal cable from the battery, and wait for 30 seconds. [CHECK] A. Turn the ignition switch to ON, and wait for at least 30 seconds. B. Clear the malfunction code stored in the memory with the Hi-Scan Pro. C. Turn the ignition switch to LOCK, and wait for 30 seconds. D. Turn the ignition switch ON, and wait for 30 seconds. E. Using the Hi-Sacn Pro, check for DTCs. There is no DTC. [HINT] Codes other than these may be output at this time, but they are not relevant to this procedure.

10.

Check the SAB squib. [PREPARATION] A. Turn the ignition switch to LOCK. B. Disconnect the negative (-) terminal cable from the battery, and wait for 30 seconds. C. Connect the SAB connector. D. Connect the negative (-) terminal cable from the battery, and wait for 30 seconds. [CHECK] A. Turn the ignition switch to ON, and wait for at least 30 seconds. B. Clear the malfunction code stored in the memory with the Hi-Scan Pro. C. Turn the ignition switch to LOCK, and wait for 30 seconds. D. Turn the ignition switch ON, and wait for 30 seconds. E. Using the Hi-Sacn Pro, check for DTCs. There is no DTC. [HINT] Codes other than these may be output at this time, but they are not relevant to this procedure.

11.

Check the BPTs squib. [PREPARATION] A. Turn the ignition swich to LOCK. B. Disconnect the negative (-) terminal cable from the battery, and wait for 30 seconds. C. Connect the BPTs connector. D. Connect the negative (-) terminal cable from the battery, and wait for 30 seconds. [CHECK] A. Turn the ignition switch to ON, and wait for 30 seconds. B. Clear the malfunction code stored in the memory with the Hi-Scan Pro. C. Turn the ignition switch to LOCK, and wait for 30 seconds. D. Turn the ignition switch to ON, and wait for 30 seconds. E. Using the Hi-Scan Pro, check for DTCs. There is no DTC. [HINT] Codes other than these may be output at this time, but they are not relevant to this procedure.

12.

Check the Satellite sensors. [PREPARATION] A. Turn ignition switch to LOCK. B. Disconnect the negative (-) terminal cable from the battery, and wait at least 30 seconds. C. Connect the Satellite sensor connector. D. Connect the negative (-) terminal cable from the battery, and wait at least 30 seconds. [CHECK] A. Turn the ignition switch to ON, and wait at least 30 seconds. B. Clear the malfunction code stored in memory with Hi-scan. C. Turn the ignition switch to LOCK, and wait at least 30 seconds. D. Turn the ignition switch to ON, and wait at least 30 seconds. E. Using the Hi-Scan Pro, check for DTCs. There is no DTC. [HINT] Codes other than these may be output at this time, but they are not relevant to this procedure.

13.	Check the Clock spring. [PREPARAION] A. Turn the ignition switch to LOCK. B. Disconnect the connector between the SRSCM and the clock spring. [CHECK] Turn the ignition switch ON, and measure the voltage between the DAB high side and the body ground. Voltage : 0V

DTC

B1346 B1347

DAB resistance too high (R ≥ 6.70 Ω) DAB resistance too low (R ≤ 1.06 Ω)

DTC Detecting Condition	Trouble Area
• Too high or low resistance between DAB high (+) wiring harness and DAB low (-) wiring harness of squib.	• DAB squib
• DAB malfunction • Clock spring malfunction • SRSCM malfunction	• Clock spring • SRSCM • Wire harness

1.

Preparation (1) Disconnect the negative (-) terminal cable from the battery, and wait at least 30 seconds. (2) Remove the DAB module. (3) Disconnect the connectors of the PAB, left and right side airbags, belt pretensioners and satellite sensors. (4) Disconnect the SRSCM connector. Place the DAB with the front surface facing upward.

2.

Check the DAB resistance. [PREPARATION] Release the airbag activation prevention mechanism on SRSCM side of airbag squib side. Connect the dummy (0957A-38200) and dummy adapter (0957A-38400)to the clock spring side connector. Never attempt to measure the circuit resistance of the airbag module (squib) even if you are using the specified tester. Before checking the resistance, you have to insert the shorting bar insert plastic that is attached to the diagnosis checker into the SRSCM connector. [CHECK] Measure the resistance between the DAB high (+) and low (-). 1.80 Ω ≤ R ≤ 3.40 Ω

3.

Check the DAB squib. [PREPARATION] A. Turn the ignition switch to LOCK. B. Disconnect the negative (-) terminal cable from the battery, and wait for 30 seconds. C. Connect the DAB connector. D. Connect the negative (-) terminal cable to the battery, and wait for 30 seconds. [CHECK] A. Turn the ignition switch to ON, and wait for at least 30 seconds. B. Clear the malfunction code stored in the memory with the Hi-Scan Pro. C. Turn the ignition switch to LOCK, and wait for 30 seconds. D. Turn the ignition switch to ON, and wait for 30 seconds. E. Using Hi-Scan Pro, check the DTC. There is no DTC. [HINT] Codes other than these may be output at this time, but they are not relevant to this procedure.

4.

Check the clock spring. [PREPARAION] Disconnect the connector between the SRSCM clock spring, and connect the dummy connector (0957A-38200) and dummy adapter (0957A-38400) to the clockspring side connector. Before checking the resistance, you have to insert the shorting bar insert plastic that is attached to the diagnosis checker into the SRSCM connector. [CHECK] Measure the resistance between the DAB high (+) and low (-). 1.80 Ω ≤ R ≤ 3.40 Ω

DTC

B1352 B1353

PAB resistance too high (R ≥ 5.4 Ω) PAB resistance too low (R ≤ 0.4 Ω)

DTC Detecting Condition	Trouble Area
• Too high or low resistance between PAB high (+) wiring harness and PAB low (-) wiring harness of squib.	• PAB squib
• PAB malfunction • SRSCM malfunction	• SRSCM • Wire harness

1.

Preparation (1) Disconnect the negative (-) terminal cable from the battery, and wait at least 30 seconds. (2) Remove the DAB module. (3) Disconnect the connectors of the PAB, left and right side airbags, belt pretensioners and satellite sensors. (4) Disconnect the SRSCM connector. Place the DAB with the front surface facing upward.

2.

Check the PAB resistance. [PREPARATION] Release the airbag activation prevention mechanism on the SRSCM side of the airbag squib side. Connect the dummy (0957A-38200) and dummy adapter(0957A-38300) to PAB connector of the SRSCM connector side. Before checking the resistance, you have to insert the shorting bar insert plastic that is attached to the diagnosis checkerinto the SRSCM connector. [CHECK] Measure the resistance between the PAB high (+) and the PAB low (-). 1.6 Ω ≤ R ≤ 2.8 Ω

3.

Check the PAB squib. [PREPARATION] A. Turn the ignition switch to LOCK. B. Disconnect the negative (-) terminal cable from the battery, and wait for 30 seconds. C. Connect the PAB connector. D. Connect the negative (-) terminal cable to the battery, and wait for 30 seconds. [CHECK] A. Turn the ignition switch to ON, and wait for at least 30 seconds. B. Clear the malfunction code stored in the memory with the Hi-Scan Pro. C. Turn the ignition switch to LOCK, and wait for 30 seconds. D. Turn the ignition switch to ON, and wait for 30 seconds. E. Using Hi-Scan Pro, check the DTC. There is no DTC. [HINT] Codes other than these may be output at this time, but they are not relevant to this procedure.

DTC

B1378 B1379 B1382 B1383

DSAB Resistance too high (R ≥ 5.4 Ω) DSAB Resistance too low (R ≤ 0.4 Ω) PSAB Resistance too high (R ≥ 5.4 Ω) PSAB Resistance too low (R ≤ 0.4 Ω)

DTC Detecting Condition	Trouble Area
• Too high or low resistane between SAB high (+) wiring harness and SAB low (-) wiring harness of squib.	• SAB squib
• SAB malfunction • SRSCM malfunction	• SRSCM • Wire harness

1.

Preparation (1) Disconnect the negative (-) terminal cable from the battery, and wait at least 30 seconds. (2) Remove the DAB module. (3) Disconnect the connectors of the PAB, left and right side airbags, belt pretensioners and satellite sensors. (4) Disconnect the SRSCM connector. Place the DAB with the front surface facing upward.

2.

Check the SAB resistance. [PREPARATION] Release the airbag activation prevention mechanism on the SRSCM side of the airbag squib side. Connect the dummy (0957A-38200) and dummy adapter(0957A-38300) to the SAB connector of the SRSCM connector side. Before checking the resistance, you have to insert the shorting bar insert plastic that is attached to the diagnosis checkerinto the SRSCM connector. [CHECK] Measure the resistance between the SAB high (+) and the SAB low (-). 1.6 Ω ≤ R ≤ 2.8 Ω

3.

Check the SAB squib. [PREPARATION] A. Turn the ignition switch to LOCK. B. Disconnect the negative (-) terminal cable from the battery, and wait for 30 seconds. C. Connect the SAB connector. D. Connect the negative (-) terminal cable to the battery, and wait for 30 seconds. [CHECK] A. Turn the ignition switch to ON, and wait for at least 30 seconds. B. Clear the malfunction code stored in the memory with the Hi-Scan Pro. C. Turn the ignition switch to LOCK, and wait for 30 seconds. D. Turn the ignition switch to ON, and wait for 30 seconds. E. Using Hi-Scan Pro, check the DTC. There is no DTC. [HINT] Codes other than these may be output at this time, but they are not relevant to this procedure.

DTC

B1361 B1362 B1367 B1368

DBPT Resistance too high (R ≥ 5.4 Ω) DBPT Resistance too low (R ≤ 0.4 Ω) PBPT Resistance too high (R ≥ 5.4 Ω) PBPT Resistance too low (R ≤ 0.4 Ω)

DTC Detecting Condition	Trouble Area
• Too high or low resistane between BPT high (+) wiring harness and BPT low (-) wiring harness of squib.	• BPT squib
• BPT malfunction • SRSCM malfunction	• SRSCM • Wire harness

1.

Preparation (1) Disconnect the negative (-) terminal cable from the battery, and wait at least 30 seconds. (2) Remove the DAB module. (3) Disconnect the connectors of the PAB, left and right side airbags, belt pretensioners and satellite sensors. (4) Disconnect the SRSCM connector. Place the DAB with the front surface facing upward.

2.

Check the BPT resistance. [PREPARATION] Release the airbag activation prevention mechanism on the SRSCM side of the airbag squib side. Connect the dummy (0957A-38200) and dummy adapter(0957A-38300) to the BPT connector of the SRSCM connector side. Before checking the resistance, you have to insert the shorting bar insert plastic that is attached to the diagnosis checker into the SRSCM connector. [CHECK] Measure the resistance between the BPT high (+) and the BPT low (-). 1.6 Ω ≤ R ≤ 2.8 Ω

3.

Check the BPT squib. [PREPARATION] A. Turn the ignition switch to LOCK. B. Disconnect the negative (-) terminal cable from the battery, and wait for 30 seconds. C. Connect the BPT connector. D. Connect the negative (-) terminal cable to the battery, and wait for 30 seconds. [CHECK] A. Turn the ignition switch to ON, and wait for at least 30 seconds. B. Clear the malfunction code stored in the memory with the Hi-Scan Pro. C. Turn the ignition switch to LOCK, and wait for 30 seconds. D. Turn the ignition switch to ON, and wait for 30 seconds. E. Using Hi-Scan Pro, check the DTC. There is no DTC. [HINT] Codes other than these may be output at this time, but they are not relevant to this procedure.

DTC	B1400	Satellite left side defect
	B1403	Satellite right side defect
	B1409	Satellite left communication error
	B1410	Satellite right communication error

1.

Preparation (1) Disconnect the negative (-) terminal cable from the battery, and wait at least 30 seconds. (2) Remove the DAB module. (3) Disconnect the connectors of the PAB, left and right side airbags, belt pretensioners and satellite sensors. (4) Disconnect the SRSCM connector. Place the DAB with the front surface facing upward.

2.	Check satellite circuit (communication error). [PREPARATION] Check continuity between the SRSCM connector and the satellite connector as high (+) and high, low (-) and low (-). OK : Continuity

3.

Check the satellite sensor (defect). [PREPARATION] A. Turn the ignition switch to LOCK. B. Disconnect the negative (-) terminal cable from the battery, and wait for 30 seconds. C. Connect the satellite connector. D. Connect the negative (-) terminal cable to the battery, and wait for 30 seconds. [CHECK] A. Turn the ignition switch to ON, and wait for at least 30 seconds. B. Clear the malfunction code stored in the memory of the Hi-Scan Pro. C. Turn the ignition switch to LOCK, and wait for 30 seconds. D. Turn the ignition switch to ON, and wait for 30 seconds. E. Using the Hi-Scan Pro, check DTC. There is no DTC. [HINT] Codes other than these may be output at this time, but they are not relevant to this check.

DTC

B1511 B1512 B1513 B1514

Driver seat belt switch open/short to Battery Driver seat belt switch short to GND Passenger seat belt switch open/short to Battery Passenger seat belt switch short to GND

1.	Preparation

2.	Check buckle switch sensor circuit (Short to GND/Battery). [CHECK] Measure the voltage and resistance of the seat belt switch high and body ground between the SRSCM connector and the seat belt switch connector. Resistance : ∞ Voltage : 0V

3.	Check the seat belt switch [CHECK] Check the resistance with the switch on and off. SWITCH OPEN : R = 4KΩ ± 10% (Belted) SWITCH OPEN : R = 1KΩ ± 10% (Unbelted)

DTC

B2500

Warning lamp failure

1.	Check the fuse. [PREPARATION] A. Remove airbag fuse and airbag warning lamp fuse from the junction block. B. Inspect the state of the fuses. C. Replace if necessary.

2.	Check the SRS warning lamp circuit. [PREPARATION] A. Connect the negative (-) terminal cable to the battery. B. Turn the ignition switch to ON. [CHECK] A. Measure voltage at the harness side connector of the SRSCM. Voltage : 9-16 V B. Check the SRS SRI (Service Reminder Indicator). OK : SRS SRI ON

DTC

B1620 B1650 B1655 B1657 B1661

Airbag unit internal failure SRSCM crash recorded Side airbay crash recorded Crash recorded-Belt pretensioner only ECU mismatching

1.	Functional readiness of the firing circuit activation transistors.

2.	Adequacy of deployment energy reserves.

3.	Safing sensor integrity : detection of faulty closure.

4.	Plausibility of accelerometer signal.

5.	Operation of SRSCM components.

DIAGNOSIS WITH SCAN TOOL

1.	Connect the Hi-Scan Pro DLC to the vehicle's data link connector located under neath the dash panel.

2.	Turn the ignition key to the "ON" position and turn the Hi-Scan Pro ON.

3.	Perform the SRS diagnosis according to the vehicle model configuration.

4.	If a fault code is assured, then replace the component. Never attempt to repair the component.

5.	If the Hi-Scan Pro finds that a component of the system is faulty, there is a possibility that the fault is not in the component, but in SRS wiring or connector.

R ≤ 1.06Ω	Resistance too low	Fault definitely detected
1.80Ω ≤ R ≤ 3.40Ω	Resistance whithin tolerance	Definitely no fault detected
R ≥ 6.70Ω	Resistance too high	Fault definitely detected
1.06Ω < R < 1.80Ω 3.40Ω < R < 6.70Ω	Tolerance band	Fault may or may not be detected

R ≤ 0.4Ω	Resistance too low	Fault definitely detected
1.6Ω ≤ R ≤ 2.8Ω	Resistance whithin tolerance	Definitely no fault detected
R ≥ 5.4Ω	Resistance too high	Fault definitely detected
0.4Ω < R < 1.6Ω 2.8Ω < R < 5.4Ω	Tolerance band	Fault may or may not be detected

DTC No.	Fault description
B1111	Battery voltage too high
B1112	Battery voltage too low
B1346	Driver airbag (DAB), Resistance too high
B1347	Driver airbag (DAB), Resistance too low
B1348	Driver airbag (DAB), Short to GND
B1349	Driver airbag (DAB), Short to Battery
B1352	Passenger airbag (PAB), Resistance too high
B1353	Passenger airbag (PAB), Resistance too low
B1354	Passenger airbag (PAB), Short to GND
B1355	Passenger airbag (PAB), Short to Battery
B1361	Driver seat belt pretensioner (DBPT), Resistance too high
B1362	Driver seat belt pretensioner (DBPT), Resistance too low
B1363	Driver seat belt pretensioner (DBPT), Short to GND
B1364	Driver seat belt pretensioner (DBPT), Short Battery
B1367	Passenger seat belt prestensioner (PBPT), Resistance too high
B1368	Passenger seat belt prestensioner (PBPT), Resistance too low
B1369	Passenger seat belt prestensioner (PBPT), Short to GND
B1370	Passenger seat belt prestensioner (PBPT), Short to Battery
B1378	Driver side airbag (DSAB), Resistance too High
B1379	Driver side airbag (DSAB), Resistance too Low
B1380	Driver side airbag (DSAB), Short to GND
B1381	Driver side airbag (DSAB), Short to Battery
B1382	Passenger side airbag (PSAB), Resistance too high
B1383	Passenger side airbag (PSAB), Resistance too low
B1384	Passenger side airbag (PSAB), Short to GND
B1385	Passenger side airbag (PSAB), Short to Battery
B1400	Satellite sensor driver side defect
B1401	Satellite sensor driver side short to GND
B1402	Satellite sensor driver side open/short to battery
B1403	Satellite sensor passenger side defect
B1404	Satellire sensor passenger side short to GND
B1405	Satellire sensor passenger side open/short to battery
B1409	Satellite sensor driver side communication error
B1410	Satellite sensor passenger side communication error
B1511	Driver seat belt buckle switch open/short to battery
B1512	Driver seat belt buckle switch short to GND
B1513	Passenger seat belt buckle switch open/short to battery
B1514	Passenger seat belt buckle switch short to GND
B1620	Airbag unit internal failure
B1650	SRSCM crash recorded
B1655	Side airbag crash recorded
B1657	Crash recorded-Belt pretensioner only
B1661	ECU mismatching
B2500	Warning lamp failure

• The DAB is located in the steering wheel. • The PAB is located in the crash pad. • The DSAB is located in the out side of driver's seat. • The PSAB is located in the out side of passenger's seat.